DynaVap Guide: Which DynaVap suits you?
Share
DynaVap Guide 2026: M7 / M7XL, UniDyn, WoodWynd, VonG (i)/(X), HyperDyn & beginner models compared
- Try it out for less: The G3 – glass body, 0.05 g chamber, lighter included.
- Best starting point with room to expand: The B2 – stainless steel, 0.075 g, fits all DynaVap tips and induction heaters.
- The daily driver: M7 / M7XL – 0.1 g, Adjust-a-Bowl, six airflow settings on the XL.
- Lightest titanium setup: The UniDyn – one-piece UniBody, BallR Cap, just two O-rings.
- For water filters: VonG (i) – full-titanium construction with 10 mm and 14 mm tapers.
- Large chamber: HyperDyn – 0.25 g Big Bowl, Hyper Cap, seven airflow settings.
DynaVap quick start: how the “click” works in 60 seconds
- Filling: loosely fill the chamber (don't pack it down). Depending on the model, that's 0.05 g (G3) to 0.25 g (HyperDyn) – the grind should be medium-fine, not powdery.
- Heating: rotate the cap evenly until it clicks. Keep the flame at the edge of the cap, not directly in the middle – and never near wooden or silicone parts.
- Draw: slowly and steadily – depending on the model, directly through the mouthpiece or through the water adapter. Wait 3–5 seconds after the click before drawing: the results will be noticeably more even.
- Cooldown: wait for the second click (the cooldown click) before heating again. Expect two to three heating cycles per bowl.
- Milder, more flavor-focused: heat for less time (remove the flame sooner), wait longer after the click, and draw slowly.
- Denser, stronger: heat for a moment past the click and draw more quickly.
- Airflow: With the M7, M7XL, UniDyn, VonG X, and HyperDyn, you can also adjust it using the airport or condenser depth – tighter = hotter and denser, more open = cooler and milder.
What do you heat the DynaVap with? Lighter, torch, or induction
- Single-flame torch (DynaTorch): Included with The B, The B2, and the M7 / M7XL; the G3 comes with a Clipper Torch. Note: The torches are delivered unfilled – you’ll need to buy butane separately. This is the cheapest and most portable option.
- Triple-flame torch: The The VonG (i) Starter Set includes a Cyclone triple-flame torch. More flames mean heating to the click more evenly and quickly, with less turning needed.
- Induction heater: The most repeatable method – insert the Cap and wait for the click, with no flame and no need for wrist technique. For WoodWynd, DynaVap explicitly recommends this because it guarantees that no flame comes into contact with the wood. Unlike the glass models, the The B2 is also induction-compatible.
- Important exception: For the DynaVap G3, the manufacturer advises against induction heaters such as “The Wand” – the glass body isn’t designed for them. Stick with a flame for this one.
1) Beginners & budget: The B, The B2, The G3 (simple, easy to learn)
DynaVap – The G3: hassle-free, sturdy, a great entry point
The DynaVap G3 Vaporizer is an extremely straightforward entry point: few frills, easy to handle, and ideal if you simply want to try DynaVap. Use case: at home & on the go, if you’re looking for a low-maintenance setup. What makes it special: The G3 consists of just two parts – a Captive Cap and a glass UniBody, with the tip and midsection made from a single piece, plus an integrated glass screen.
- Chamber: 0.05 g – the smallest in the range, making it ideal for microdosing.
- Material: Glass uni-body with a glass chamber and integrated glass screen, plus the Captive Cap.
- Design: Tri-lobe shape with anti-roll feature – won't roll off the table.
- Included: G3, Clipper Torch (random color), and DynaVap tin.
- Please note: No induction heater, and tips, condensers, and dosing capsules from the other models are not compatible. The G3 is compatible with the Standard Cap, Low Temp Cap, and Perforated Cap.
DynaVap – The B: an easy entry point with case (everyday setup)
The DynaVap The B is a great “first daily”: straightforward, quick to use, and ideal for DynaVap storage thanks to the case. Use case: when you want a set you can simply grab and go – without loose parts flying around. The tip, condenser, and CCD screen are made of medical-grade stainless steel, while the stem is made of food-grade silicone – making it durable and comfortable to grip.
- Material: Stainless steel (tip, condenser, CCD screen) with a silicone stem · made in the USA.
- Until the click: approx. 5–7 seconds with a single flame.
- Water filter: 10 mm cone – fits directly, no adapter needed.
- Included: The B (Captive Cap, Tip, silicone stem, condenser), metal case, and DynaTorch.
- Extra: 90-day money-back guarantee from DynaVap · upgradeable later, because the parts fit the DynaVap system.
DynaVap – The B2: the upgrade for “more” (with case)
The The B2 is for anyone who wants to start with something a little more “grown-up”: more presence in the hand, a refined feel, and a set that looks premium enough for everyday use. Use case: if you love the DynaVap concept but want to feel “better equipped” from the start. The key advantage over the G3: the B2 is fully upgradeable—it works with all DynaVap tips and is compatible with induction heaters.
- Chamber: 0.075 g—a little more than the G3, but still firmly in the microdosing range.
- Material: Stainless steel (cap, tip, condenser, CCD screen) with a high-temperature-resistant silicone stem.
- Compatibility: all DynaVap tips, induction heaters like The Wand, SlingStash · 10 mm cone for water filters.
- What’s included: B2, DynaVap tin, and DynaTorch (unfilled).
- Design: Anti-roll, grippy silicone stem that’s easy to rotate while heating.
- G3: The most affordable entry point, glass body, 0.05 g—but no induction heater compatibility and no option to expand with accessories.
- The B vs. B2: Technically very similar (stainless steel + silicone stem, 10 mm cone, DynaTorch included). The B2 is the newer version, with a 0.075 g chamber and explicit compatibility with all tips and induction heaters.
- Our recommendation: If you think you’ll stick with DynaVap, go for the B2—it grows with you. If you just want to see whether the concept suits you, the G3 is more than enough.
2) The “sweet spot” for many: DynaVap M7 & M7XL (with case)
DynaVap – M7: compact, direct, suitable for daily use
The M7 is our recommendation if you want a “real” DynaVap you can use every day: sturdy, comfortable in the hand, and with a setup that’s quick to keep clean. Use case: daily driver for short sessions—perfect if you value efficiency. Technically, it features the Finless Tip design, which reduces heat transfer toward the Stem by up to 20%—the device stays noticeably cooler in your hand while heating.
Our DynaVap M7 and M7 XL hands-on review shows you how to hit the Click reliably, which heat source is right for you, and exactly how the M7 and M7 XL differ.
- Material: entirely stainless steel, textured Stem for better grip.
- Chamber: 0.1 g, can be halved with Adjust-a-Bowl.
- Airflow: Airport design with rocker switch.
- Included: M7 (Cap, stainless steel Tip with CCD screen and O-rings, Stem, condenser), Tin Case, DynaTorch (unfilled).
- Variants: In addition to the classic M7, there’s the M7 TwoToniuM in a two-tone design (technically identical) and the M7 XL Stealth in a dark finish.
DynaVap – M7XL: more length, more relaxed handling
The M7XL is for anyone who likes the M7 principle but wants a “bigger” feel when holding and drawing. Use case: if you prefer a more relaxed grip, like having more distance from the heat, or simply love the XL handling. The real difference, though, is inside: the M XL Condenser Assembly offers six airflow settings via the condenser depth, and the longer path to the mouthpiece noticeably cools the vapor.
3) Premium feel: The UniDyn & WoodWynd (for aesthetics & “favorite piece” vibes)
DynaVap – The UniDyn: clean, modern, very “straight”
The UniDyn looks extremely modern and streamlined – a setup you'll be happy to leave on the table. Use case: when you want a premium design that remains super practical for everyday use (and fits easily into your accessory/storage setup). The clever part is the one-piece UniBody made of medical-grade titanium: the tip and stem are seamlessly connected, with a HypoTherm heat break (T-Break) in between to keep heat away from the chamber.
- Material: medical-grade titanium with scratch-resistant DuraDyn coating, stainless steel CCD screen.
- Cap: BallR Cap with convection – not the classic Captive Cap, but the more flavor-focused version.
- Chamber: 0.1 g, reducible with Adjust-a-Bowl.
- Airflow: 7 settings via the adjustable condenser.
- Practical: grooved tip for grinding on the go · only 2 O-rings in total, so extremely low maintenance · 10 mm joint for water filters.
- Scope of delivery: UniDyn (BallR Cap, titanium tip & stem with CCD, titanium condenser with mouthpiece, 2 O-rings) and DynaVap tin.
DynaVap – WoodWynd: wood look, warm feel, everyday premium
The DynaVap WoodWynd is for those who prefer a “warmer” look and feel. It not only looks elegant, but also makes everyday handling really pleasant. Use case: if you like having a beautiful setup but still want something fully suited to daily use. The stem is made of Padauk hardwood with stainless steel crowns and is shaped like an hourglass – each piece has its own grain, so yours will look different from your neighbor’s.
- Material: Padauk hardwood stem with stainless steel crowns, Helix titanium tip, stainless steel Cap.
- Helix Tip: thicker chamber walls – retains heat longer and therefore delivers more even draws.
- Mouthpiece: triple Helix without O-rings – one less wear part.
- Water filter: fits directly, without a taper into 10 mm openings.
- Important when heating: Always aim the flame at the Cap, never at the wooden stem. DynaVap explicitly recommends an induction heater for the WoodWynd.
- Included: WoodWynd (wood stem, Helix Tip, condenser, Cap) and DynaVap tin · fits in XL DynaStash or SlimStash.
4) For water & a “smooth” experience: VonG DynaVap (i), VonG X + starter sets
DynaVap – The VonG (i): titanium setup for water
The The VonG (i) is for anyone who enjoys using their DynaVap with a water filter or simply wants a setup that feels like a “tool”: durable, high-quality, and very well thought out. Use case: at home with glass, when you enjoy smooth draws. The tip, stem, and condenser are made entirely of titanium, and it also comes with a replaceable, rotatable titanium sleeve – and the whole thing can be completely disassembled without tools.
- Material: titanium tip, stem, and condenser, with a rotatable titanium sleeve.
- Connection: tapered mouthpiece in 10 mm and 14 mm – fits directly into female water pipe openings.
- Chamber: can be halved with Adjust-a-Bowl.
- Included: cap, titanium tip with CCD screen and O-rings, titanium stem with sleeve, standard titanium condenser – plus a free Zebrawood SlimStash.
Starter Set – The VonG (i): an “everything included” start for your water setup
If you don’t want to hunt down all the pieces individually, the Starter Set The VonG (i) is incredibly convenient. Use case: you want to get off to a smooth start with a well-matched accessory setup and proper DynaVap storage. Along with the device, the DynaVap Starter Kit includes everything you’d otherwise reorder after two weeks: a triple-flame Cyclone torch (unfilled), a walnut DynaStash, DynaWax for the threads, a titanium CCD screen, plus 5 high-temperature O-rings and condenser O-rings.
DynaVap – The VonG X: water use case with an “X” vibe
The The VonG X is the version for anyone who wants the VonG use case (water/smooth), but feels more drawn to the “X” in terms of looks and setup. Use case: when you enjoy using your DynaVap with water and want a distinctive, standalone setup. Technically, it’s a hybrid construction: a titanium body with a substantial stainless steel tip that stores more heat and therefore extracts more powerfully than pure titanium.
- Material: titanium body + stainless steel tip, two-tone DuraDyn finish.
- Chamber: 0.1 g, can be halved with Adjust-a-Bowl.
- Airflow: Airport is at the mouthpiece and opens or closes with a twist.
- Connection: 10 mm and 14 mm tapers, body with a 14 mm ground joint at both ends.
- Condenser: flexible – connects to either the tip or the mouthpiece.
- Version: Also available as the VonG X Stealth in a dark finish.
5) Maximum setup: HyperDyn (if you want “big”)
The HyperDyn is the pick for anyone who loves DynaVap and simply wants more “presence” in their setup. Use case: at home, if you like having a powerful, solid device in your hand - including a case for tidy DynaVap storage. “Big” is meant literally here: with its 0.25 g Big Bowl, the HyperDyn holds two and a half times as much as an M7 and five times as much as a G3.
- Chamber: 0.25 g - the largest in the DynaVap range.
- Material: medical-grade, hardened and colored titanium with scratch-resistant DuraDyn coating.
- Cap: Hyper Cap made of titanium with Captive Cap technology.
- Airflow: 7 settings.
- Connection: 10 mm and 14 mm taper for water filters.
- Contents: Hyper Cap, Hyper titanium tip with CCD and O-rings, titanium condenser assembly with mouthpiece, HyperDyn titanium stem, dosing capsule and tin.
- Modular: compatible with previous DynaVap midsections, tips and mouthpieces.
Bonus: Starter Set The M7 Walnut (for a “complete & stylish” start)
Direct comparisons: DynaVap G3 vs M7, B2 vs M7, UniDyn vs M7 & HyperDyn vs M7XL
DynaVap G3 vs M7
Whether you’re searching for DynaVap G3 vs M7 or DynaVap M7 vs G3, they represent two completely different philosophies. The G3 is glass, two-piece, 0.05 g, and deliberately simple - no airflow control, no tips, no induction heater. The M7 is all metal, 0.1 g with Adjust-a-Bowl, has adjustable airflow, and can be expanded in any direction. If you love the taste of glass and don’t need much: G3. If you want a device for years to come: M7.
DynaVap B2 vs M7
We get this question both ways - as B2 vs M7 and as DynaVap M7 vs B2. The B2 has a silicone stem and a 0.075 g chamber, while the M7 is all stainless steel with a 0.1 g chamber, Finless Tip, and Airport. Both work with all tips and induction heaters. In practice, that means the B2 is the more affordable entry point into the same ecosystem, while the M7 gives you airflow control and a cooler feel when heating. If you can afford the extra cost, the M7 is the device most people stick with long-term.
DynaVap UniDyn vs M7
Same chamber size (0.1 g), different design. The UniDyn is titanium rather than stainless steel, making it significantly lighter. It has 7 rather than one Airport setting, a BallR Cap with convection instead of the Captive Cap, and needs only two O-rings. The M7 is more robust in the sense of being “indestructible” and is cheaper. In short: with the DynaVap M7 vs UniDyn, you’re choosing between flavor, fine control, and weight (UniDyn) and value for money plus peace of mind (M7). The same generally applies to UniDyn vs M7 XL, except that the XL comes closer to the UniDyn with its 6 airflow settings.
HyperDyn vs M7XL
The chamber is the deciding factor here: 0.25 g for the HyperDyn versus 0.1 g for the M7XL. The HyperDyn is for longer sessions and sharing with two or three people, plus it offers titanium construction, 7 airflow settings, and a 14 mm connection. The M7XL remains the better everyday and on-the-go device. If you mostly vape alone and keep sessions short, the HyperDyn would simply be overkill.
VonG (i) vs VonG X
Both are designed for use with a water filter and have 10 mm and 14 mm tapers. The VonG (i) is all titanium - lighter, with a rotating sleeve and tool-free disassembly. The VonG X features a heavy stainless steel tip on a titanium body, delivering more powerful extraction, and regulates airflow by rotating the mouthpiece. For titanium purists: (i). More punch per draw: X.
Decoding DynaVap model names: VapCap, “The M 2021/2022,” and the components
- VapCap is DynaVap's product name for the devices themselves – if you read “DynaVap VapCap,” it doesn't refer to a special model.
- “The M 2020 / 2021 / 2022”: The M series was released as an annual model for years. Today's M7 is the seventh generation of this line. So if you're looking for DynaVap 2021, DynaVap 2022, or DynaVap M 2021, the M7 is the current successor. Since the DynaVap system has a modular design, accessories for older M models will generally still fit – the exception is the G3 with its glass body.
- Cap: the cap that clicks. It comes in several versions – Captive Cap (standard), BallR Cap (convection, used in the UniDyn), Hyper Cap, and Armored Cap.
- Tip: the part with the chamber. It determines the fill amount and extraction character – e.g., the Finless Tip on the M7 or the Helix Tip on the WoodWynd.
- Stem: the middle section you hold in your hand – made of stainless steel, titanium, silicone, wood, or glass.
- Condenser: the tube inside the stem that cools the vapor. On many models, its depth regulates the airflow.
- CCD: the screen at the bottom of the chamber that keeps your material in place.
- Adjust-a-Bowl: the option to halve the chamber by adjusting the condenser position – microdosing without a second device.
- Stealth versions: visually dark finishes of well-known models (e.g., B2 Stealth, M7 XL Stealth, VonG X Stealth) – technically identical to the respective standard model.
DynaVap accessories, storage & cleaning (so it always tastes great)
- DynaVap cap: The fastest way to change its character. The BallR Cap for more convection and flavor, the Hyper Cap and Thermal Hyper Cap for large chambers, the Armored Cap for robust handling – plus the classic VapCap caps as replacements.
- Tips: change the chamber size and extraction without needing a new device.
- Dosing capsules: pre-fill them and swap them on the go – available in standard and Hyper versions. The HyperDyn comes with one included.
- Wear parts: CCD screens, condenser seal rings, high-temperature O-ring kits, and titanium condensers – replace them once or twice a year, depending on how often you use the device.
- Maintenance kits: DynaKit Basic and DynaKit Maintenance bundle exactly what you need for taking it apart and servicing it.
- DynaVap cases & storage: from the small SnapStash to the SlingStash and DynaBank, all the way to the wooden DynaStash – the latter is also included with the starter kits. For everyday use, though, the included tin also works as a DynaVap M7 case.
- DynaGrynd: the right grinder if you want a consistent grind – with chambers this small, it makes more difference than you might think.
Overview: Which DynaVap is right for you?
| Model | Who is it for? | Chamber | Material | Price range | Key feature | Link |
|---|---|---|---|---|---|---|
The G3
|
Budget-friendly & “just try it” | 0.05 g | Glass UniBody | € · Entry-level | Just 2 parts, torch included · no induction heater | View → |
The B
|
Beginner-friendly, straightforward | Not specified | Stainless steel + silicone | €€ · Entry+ | Case + DynaTorch included, 10-mm taper | View → |
The B2
|
Beginners looking to upgrade | 0.075 g | Stainless steel + silicone | €€ · Entry+ | Compatible with all tips + induction heaters | View → |
M7
|
Daily driver | 0.1 g Can be halved |
Stainless steel | €€€ · Mid-range | Finless Tip (−20 % heat), airport | View → |
M7XL
|
Daily + XL handling | 0.1 g Can be halved |
Stainless steel | €€€ · Mid-range | 6 airflow settings, longer cooling path | View → |
The UniDyn
|
Premium, clean & modern | 0.1 g Adjustable |
Titanium UniBody | €€€ · Mid-range | BallR Cap, 7 airflow settings, just 2 O-rings | View → |
WoodWynd
|
Premium with a wooden vibe | Helix Tip | Padauk wood + titanium | €€€€ · High-end | O-ring-free mouthpiece, fits 10 mm directly | View → |
The VonG (i)
|
Water setup | Can be halved | All titanium | €€€€ · High-end | 10 & 14 mm taper, SlimStash free | View → |
The VonG X
|
Water + distinctive look | 0.1 g Can be halved |
Titanium + stainless steel | €€€€ · High-end | Rotating airport on the mouthpiece | View → |
HyperDyn
|
Maximum capacity, longer sessions | 0.25 g Big Bowl |
Hardened titanium | €€€€€ · Premium | Hyper Cap, 7 airflow settings, dosing capsule | View → |
VonG (i) starter set
|
Get started with water, no guesswork | like VonG (i) | Titanium core | €€€€€ · Premium | Cyclone burner, walnut DynaStash, O-rings | View → |
M7 Walnut starter set
|
“Complete & stylish” daily starter | like M7 | Stainless steel + walnut | €€€€ · High-end | DynaStash, lighter, DynaWax, O-rings | View → |
Frequently asked questions about DynaVap
Which DynaVap is the best?
There’s no universally best option - but here’s an honest ranking: cheapest entry point The G3, best entry point with room to grow The B2, best overall package M7 / M7XL, finest control The UniDyn, for water VonG (i), for long sessions HyperDyn. If you can’t decide and want just one device: M7XL.
Do I need a special lighter?
A regular lighter is not reliable - you need a jet flame (torch) or an induction heater. The B, The B2, and M7 / M7XL include a DynaTorch; the G3 includes a Clipper Torch. All burners come unfilled, so you’ll need to buy butane separately.
How much fits in the chamber?
Depending on the model: 0.05 g for the G3, 0.075 g for the B2, 0.1 g for the M7, M7XL, UniDyn, and VonG X, and 0.25 g for the HyperDyn. For all models with Adjust-a-Bowl, you can reduce the chamber to half size. DynaVap does not specify a gram amount for The B - in practice, it holds about the same as the B2.
Will a DynaVap fit my bong or water pipe?
Yes. The B, The B2, M7, and UniDyn have a 10 mm taper; the WoodWynd even fits directly into 10 mm openings without a taper. VonG (i), VonG X, and HyperDyn also come with 14 mm fittings, so they fit the common larger joints too - no extra adapter needed.
What does “DynaVap 2021” or “The M 2022” mean?
These are the earlier annual editions of the M series - also searched for as DynaVap 2020, DynaVap 2022, or DynaVap M 2022. The current M7 is the seventh generation and its current successor. Accessories from the DynaVap system are largely cross-compatible - only the G3 is an exception because of its glass body.
Can I use an induction heater?
Yes, for all metal and titanium models - this is explicitly approved for The B2, and DynaVap even recommends it for the WoodWynd. The manufacturer advises against it for the G3, so use a flame with this one.
How do I clean my DynaVap properly?
Disassemble it, clean the metal parts with warm water and a brush, soak them in isopropyl alcohol occasionally, and dry them thoroughly. Soak O-rings only briefly, and never soak wooden parts. See the Accessories & Cleaning section for details.
Is a starter set worth it, or should I buy everything separately?
If you know you’ll want storage, a burner, and replacement O-rings anyway, a DynaVap set is the more convenient and usually cheaper option. If you just want to try it out first, the device with its included case and torch is plenty.