Why two Vaporizers produce different amounts at the same temperature

Vaporizer knowledge · Efficiency

Set two Vaporizer devices to the same temperature, give them the same material—and they still produce different amounts. This has been measured in a laboratory, with a 28-percentage-point difference between the best and worst device. This article explains the design factors behind this difference and what makes it larger or smaller during use.

Technical article · Approx. 10-minute read · All figures are supported by primary sources and can be verified individually at the end · Last updated: August 2026

82,7 %
of the THC it contained was transferred into the vapor by the best device in the lab test[1]
28 percentage points
Difference between the best and worst device at the same temperature setting[1]
≥ 97%
of the acid form was converted into the active form in temperature-controlled devices[1]

1 · Yield is the efficiency of a vaporizer

In briefYield describes how well a device does its job: how much of the active ingredient present it transfers into the gas phase. It is a property of the design, not the user.

Every machine that transforms something has an efficiency rating. For a heat pump, it is the ratio of electricity used to heat produced; for an espresso machine, it is the proportion of soluble compounds that actually ends up in the cup. For a Vaporizer, it is the yield: the proportion of the active ingredient present in the material that the device transfers into the gas phase. An 80 percent yield means that four-fifths end up in the vapor and one-fifth remains in the plant material.

It is important to understand what this does not mean. Yield is a laboratory value and describes only the device’s performance. It is measured as follows: Under controlled conditions, the device fills a balloon, whose contents are then chemically analyzed. What is lost again when exhaling or not absorbed by the lungs depends on the person, not the device—and is therefore not covered in this article.

That is precisely why it is so useful: It is the only metric for which different Vaporizer devices have been measured directly against one another under identical conditions. No spec sheet offers anything comparable.


2 · The measurements: five devices compared

In shortIn 2016, a Swiss laboratory tested five devices at an identical 210 °C. Yield ranged from 54.6 to 82.7 percent.

The most informative study on this topic was conducted by Lanz and colleagues and published in 2016 in PLoS ONE, an open-access journal.[1] Five commercially available devices were tested. Each received the same material and – where adjustable – was set to the same temperature of 210 °C. The researchers then measured how much THC and CBD actually made it into the vapor.

Table 1 · Active compound yield in the vapor, measured at a consistent 210 °C. All values from Lanz et al. 2016.[1] For anonymization, see the note below the table.

Device Heating method THC CBD Note
Device A Primarily convection 82,7 % 70,0 % Best result in the test lineup – and also the cheapest, most compact device
Device B Hybrid, desktop 66,8 % 56,1 % Second-best result
Device C Convection, desktop 58,4 % 51,4 % Significantly more expensive than device A, but ranked mid-range
Device D Gas-powered 55,9 % 45,9 % No temperature control; combustion was observed during testing
Device E Conduction, portable 54,6 % 56,7 % Lowest THC result, but mid-range for CBD

Two things are worth a second look. First, the best-performing device wasn’t the most expensive, but a compact portable one. So price says little about yield. Second, the gap between the best and worst results is 28 percentage points – with identical material and temperature. The difference comes down entirely to design.

Why no device names appear here The study names the models tested, and it’s freely available – anyone who wants to check can find the names there. We deliberately leave them out here for a factual reason: the test lineup dates back to 2016. Several of these devices are no longer made; others are now available only as updated successors that weren’t included in the tests. So a single measurement from back then says nothing about a current model – good or bad. The only reliable takeaway is the range: devices differ considerably at identical settings.

3 · The proportion that never leaves the chamber

In shortDepending on the design, between 17 and 45 percent of the active compound never reaches the gas phase. This proportion is the true measure of a device’s quality.

Every yield figure has a flip side: What doesn’t go into the vapor remains in the material. At 82.7 percent yield, that’s 17.3 percent; at 54.6 percent, a full 45.4 percent. Almost half.

Figure 1 · What goes from a load into the vapor

Best and weakest device in the comparison, based on the THC content. After Lanz et al. 2016.[1]

0 25 50 75 100 Anteil des enthaltenen THC (%) Gerät A bestes Ergebnis 82,7 % 17,3 % Gerät E schwächstes Ergebnis 54,6 % 45,4 %
made it into the vapor left in the material
The gray portion never left the chamber. This is precisely where two devices differ when set identically - not in the spec sheet and not in the purchase price. Original illustration based on the published yield values.

4 · What the difference means in practice

In shortTo achieve the same result, the weakest device in the test has to use around half again as much material as the best.

The yield values can be used to directly calculate how much material two devices need for the same result. The calculation is simple division: 82.7 divided by 54.6 equals 1.51. So the weakest device has to use one and a half times as much to get the same amount of active ingredient into the vapor.

Figure 2 · Material used for the same result

Relative representation, calculated from the yield values of 82.7% and 54.6%.[1]

bestes Gerät 100 % schwächstes Gerät 151 % Beide Balken liefern dieselbe Menge Wirkstoff in den Dampf. Der Überhang rechts der gestrichelten Linie wird nie verdampft.
The calculation applies to the two extremes in the test. The difference is smaller between two average devices. Original illustration.

This is what the relationship looks like across the entire test group. The right-hand column indicates how much material a device has to use relative to the best result to achieve the same output.

Table 2 · What the relative yield values mean. All figures calculated from Table 1.

Device Yield remains in the material Material used relative to
Device A 82,7 % 17,3 % 100 %
Device B 66,8 % 33,2 % 124 %
Device C 58,4 % 41,6 % 142 %
Device D 55,9 % 44,1 % 148 %
Device E 54,6 % 45,4 % 151 %

The gap between the mid-range devices is small, while the gap at the top is large. The difference in material use between Device B and Device E is only 27 percentage points - but the gap between Device A and the rest of the field is at least 24. In other words: there is no gentle slope, but an outlier at the top.

What this calculation is not A guarantee. It assumes that lab values translate directly into everyday use, and they never do completely. Grind size, fill quantity, draw speed, and the material's moisture also affect the result, sometimes considerably. The table shows an order of magnitude, not a guaranteed value for a specific device.

5 · Why almost nothing is lost: decarboxylation

In shortHeat converts the inactive acid form into the active form. With regulated devices, this succeeds more than 97 percent of the time.

In the fresh plant, the active compound is not present in its active form at all, but as an acid—THCA instead of THC. This acid form has virtually no effect. Heat first removes a carbon dioxide molecule, producing the active compound. This process is called decarboxylation.

How quickly and completely this happens depends on temperature and time. A research group systematically measured this relationship in 2016.[4] More important in practice, however, is what actually happens in the device: In a comparison test from the same year, electrically heated, temperature-controlled devices achieved conversion rates of at least 97 percent.[1]

This is good news and is rarely mentioned: Virtually nothing is lost at this stage. Anyone who “activates” their material in an oven beforehand is doing so for other uses; it isn’t necessary for the Vaporizer, because the device takes care of it during heating anyway.


6 · What changes the yield during use

In shortEven with a fixed design, yield varies: temperature, grind size, fill level, and draw speed affect how much heat reaches the material.

Temperature is the biggest lever. And it works in both directions. Lower is not automatically better: In a 2009 study, the ratio of active compounds to unwanted by-products was worst at 170 °C out of all the vaporization conditions tested; it was better at 200 and 230 °C.[3] The combustion threshold sets the upper limit. For a detailed look at which temperatures work best for what, see the temperature article in this series.

Grind size determines the surface area. The finer the material, the more surface area heat can act on. With convection devices, where hot air flows through the material, grinding evenly is therefore noticeably more important than with devices that have a heated chamber wall. However, too fine a grind is also not ideal, as it can block the airflow.

The fill level works in both directions. A device study as early as 2006 tested different amounts of material, so the fill level has long been known as a factor.[5] In practice, a chamber that is too loosely packed lets air flow past the sides, while one that is packed too tightly restricts it. With convection and hybrid devices, a loose to medium fill usually works best.

Draw speed matters especially with convection. That's where heat is generated in the airflow - anyone who draws quickly sends air through the material that has had less time to warm up. Slow, steady draws therefore usually deliver more. The article on heating principles explains which principle your device uses.

Table 3 · An overview of the adjustment factors, sorted by effect.

Adjustment What it affects Supported by Effort
Temperature Determines how much active ingredient is released and how clean the ratio to by-products is Measurement series at 170 / 200 / 230 °C[3] none
Device choice 28 percentage-point difference at identical settings Device comparison at 210 °C[1] one-time purchase
Grind size More surface area for heat transfer Based on physics, not measured for specific devices a grinder
Fill amount Controls how evenly air flows through the material studied as a factor[5] none
Draw speed With convection, determines how hot the air is when it reaches the material Based on physics, not measured for specific devices none

7 · Where the numbers end

In shortLaboratory values are no guarantee, the test field dates from 2016 - and yield is not the only property that matters anyway.

This article comes with three caveats to help put the figures in perspective.

First, measurements were taken in a laboratory, not a living room. The devices filled a balloon under controlled conditions. In everyday use, grind size, fill amount, drawing technique, and material moisture also come into play - all factors that can shift the results in either direction.

Second, the study dates from 2016, and the tested devices' successor models were not measured. The rankings from that time cannot be applied to today's devices without further testing.

Third, yield is not the only reason to choose a Vaporizer, and probably not even the most important one. The first comparative laboratory analysis in 2004 found only three accompanying compounds alongside the active ingredients in the vapor - the smoke from the same sample contained more than 111.[2] For more on the composition of vapor, see the detailed article.

What remains is still an unusually clear finding: Two devices with identical settings differed by 28 percentage points. Few other properties of a Vaporizer show a difference measured so clearly - and so little a matter of taste.


8 · Frequently Asked Questions

Why do devices differ at all when the temperature is the same?

Because the set temperature is only a target value. What matters is how much heat actually reaches the material, how evenly it is distributed, and how the airflow moves through the chamber. That’s what distinguishes two designs, even when both displays show the same number.

How big is the difference between two devices?

In the 2016 lab test, the difference in yield between the best and worst results was 28 percentage points.[1] In other words, the least effective device needed around 50 percent more material to achieve the same result. However, these figures are from devices made in 2016 and don’t apply to today’s models.

Is an expensive device automatically more efficient?

No. In the 2016 lab test, the cheapest, most compact device came out on top, while a significantly more expensive desktop device ranked in the middle.[1] Design, not price, is what matters.

Can I test my device’s yield myself?

That’s not useful. The published values come from chromatographic analyses in a lab, where the chamber contents were quantified before and after use. You can’t replicate this at home—visible discoloration or smell don’t reliably indicate the actual amount remaining.

Do I need to activate my material beforehand?

Not for the Vaporizer. The acid form converts to the active form as the device heats up; rates of at least 97 percent were measured in temperature-controlled devices.[1]

Does a low temperature produce a higher yield?

No, quite the opposite. In the 2009 test series, the ratio of active compounds to byproducts was worst at 170 °C and better at 200 and 230 °C.[3] Very low temperatures produce plenty of flavor, but little active compound.

From our store · Product recommendation

Devices where yield takes center stage

The article above deliberately mentions neither products nor device names from the study. Instead, it describes the features that the measurement data show to be important: a temperature that can be finely adjusted and then maintained, and an airflow path that carries air evenly through the material. These are devices from our range that address exactly these points through their design. We explicitly do not provide yield values from the study for them—different devices were tested at a different time.

Precisely adjustable

Arizer Solo 3 Version 2.0 Vaporizer with all-glass vapor path

Arizer Solo 3 Version 2.0

Mostly convection-based, with an all-glass vapor path and a temperature adjustable from 40 to 220 °C in one-degree increments. This lets you control the temperature as precisely as Section 6 recommends.

View Solo 3 →
Storz and Bickel Plenty Vaporizer with stainless steel cooling coil

Storz & Bickel Plenty

A desktop hybrid combining a preheated chamber and airflow, with a stainless steel cooling coil instead of plastic in the vapor path. Seven temperature settings between 130 and 202 °C cover the range discussed in Section 6.

View Plenty →

With temperature settings, airflow control, or an app

Storz and Bickel Venty Vaporizer with adjustable airflow

Storz & Bickel Venty

Precisely adjustable from 40 to 210 °C, plus continuously adjustable airflow up to 20 liters per minute. Together, these address exactly the two factors from Section 6 that make the biggest difference in everyday use: temperature and draw speed.

View Venty →
Storz and Bickel Crafty+ hybrid vaporizer with app control

Storz & Bickel Crafty+

The more affordable entry point into the same technology: hybrid heating with a ceramic-coated chamber, three preset temperatures of 180, 195, and 210 °C, and finer adjustment via the app. The three settings practically replicate the stepped approach described in Section 6.

View Crafty+ →

Sources

  1. Lanz C., Mattsson J., Soydaner U., Brenneisen R. (2016): Medicinal Cannabis: In Vitro Validation of Vaporizers for the Smoke-Free Inhalation of Cannabis. PLoS ONE 11(1): e0147286. DOI: 10.1371/journal.pone.0147286 – Primary source for all yield values (54.6–82.7%) and decarboxylation rates. Freely accessible.
  2. Gieringer D., St. Laurent J., Goodrich S. (2004): Cannabis Vaporizer Combines Efficient Delivery of THC with Effective Suppression of Pyrolytic Compounds. Journal of Cannabis Therapeutics 4(1): 7–27. DOI: 10.1300/J175v04n01_02 – Primary source for the comparison of over 111 compounds in smoke versus three in vapor.
  3. Pomahacova B., Van der Kooy F., Verpoorte R. (2009): Cannabis smoke condensate III: the cannabinoid content of vaporised Cannabis sativa. Inhalation Toxicology 21(13): 1108–1112. DOI: 10.3109/08958370902748559 – Primary source for the temperature series 170 / 200 / 230 °C.
  4. Wang M., Wang Y.-H., Avula B., Radwan M. M., Wanas A. S., van Antwerp J., Parcher J. F., ElSohly M. A., Khan I. A. (2016): Decarboxylation Study of Acidic Cannabinoids: A Novel Approach Using Ultra-High-Performance Supercritical Fluid Chromatography/Photodiode Array-Mass Spectrometry. Cannabis and Cannabinoid Research 1(1): 262–271. DOI: 10.1089/can.2016.0020 – Primary source for decarboxylation kinetics.
  5. Hazekamp A., Ruhaak R., Zuurman L., van Gerven J., Verpoorte R. (2006): Evaluation of a vaporizing device (Volcano) for the pulmonary administration of tetrahydrocannabinol. Journal of Pharmaceutical Sciences 95(6): 1308–1317. DOI: 10.1002/jps.20574 – Examined, among other things, the effect of different filling amounts.

Note: This article is intended to provide technical and scientific information about how vaporizers work and does not make any claims about the consumption of specific substances. The use of vaporizers and handling of the substances mentioned are subject to applicable laws and regulations. All yield and temperature values are from the cited literature and were determined under laboratory conditions; they are reference values and do not guarantee the performance of any particular device. The ratios in Section 4 are calculated from these laboratory values and indicate an order of magnitude, not savings guaranteed in everyday use.

Warum zwei Vaporizer Unterschiedlich liefern Blog Banner
Back to blog

Vaporizerheaven

Why Vaporizerheaven?

Carefully selected instead of just listed

With us, you won’t find everything – but the right thing. Before a Vaporizer is added to the Vaporizerheaven range, we thoroughly check it: craftsmanship, operation, reliability, and above all the real user experience in everyday life.

For us, it’s not just about technical data or big brand names. What matters is whether a device truly convinces in daily use. That’s why we only offer Vaporizers and accessories that we ourselves fully stand behind – and with which our customers also have the best experiences.

Experience directly from the official specialist dealer

Vaporizerheaven is an official dealer of numerous renowned Vaporizer brands. This means for you: guaranteed original products, reliable quality, and a dedicated contact person you can rely on.

Thanks to our many years of experience, we know the subtle differences between the individual devices very well. So we don’t recommend just any Vaporizer, but exactly the model that fits your personal needs and preferences.

Personally there for you – before and after purchase

For us, good service doesn’t end with the sale. It’s important to us that you are satisfied with your decision in the long term.

That’s why we are personally available for you – whether it’s about choosing the right device, the correct usage, or a question about your order. We take the time, listen, and find the right solution together with you.

Our commitment

Vaporizerheaven stands for carefully selected products, honest advice, and personal closeness – for a service where you are not just an order number, but a person at the center.

Recommended Use

Our products are designed for aromatherapy – for pleasant fragrance and herbal experiences.

Our service hours

We are also happy to assist you by phone with any questions about your order or for personal advice.

Monday-Friday

Available from 2 PM to 7 PM

Tel.: +49 176 63217963

Email: service@yornridge.com